Protokoll at the end of Real time sync
- Posts: 11
- Joined: 24 Jul 2021
How can I prevent the protocol from appearing at the end of each action of Real Time Sync?
- Posts: 3599
- Joined: 11 Jun 2019
What?
Do you mean the progress Window?
Do you mean the progress Window?
- Posts: 11
- Joined: 24 Jul 2021
Yes, it pops up after every single Job.
- Posts: 3599
- Joined: 11 Jun 2019
When you saved your batch file in FFS, you needed to check "Run Minimized" and "Auto Close", and "ignore errors" if you want. Open FFS, select your sync, click "save as" and overwrite it after checking those boxes.
- Posts: 11
- Joined: 24 Jul 2021
Tanks for help.
- Posts: 11
- Joined: 24 Jul 2021
Perfekt, it works finde. Only a litte cosmetic problem is
left. After the laptop is started, the batch-file opens up.
This might be related to Windows, I guess.
Many thanks for your help, you saved my life.
left. After the laptop is started, the batch-file opens up.
This might be related to Windows, I guess.
Many thanks for your help, you saved my life.
- Posts: 3599
- Joined: 11 Jun 2019
No, you must have missed the "Run minimized" box. RTS will always run the sync once before going idle. I have Windows and don't have that issue
- Posts: 11
- Joined: 24 Jul 2021
I did mark minimised and then automaticly auto close and ignore errors were set. Okay, tomorrow I'll start from scrach and let you know if it works.
- Posts: 3599
- Joined: 11 Jun 2019
Or, you put the batch file in your startup location too? You don't want to do that
- Posts: 11
- Joined: 24 Jul 2021
It's in the autostart, as proposed in some kind of manual I found in the internet. Plus I placed a copy in my documenta, but not as a .bat
- Posts: 3599
- Joined: 11 Jun 2019
Just the RTS file goes in your startup.
Move your batch file somewhere else and make sure you modify your RTS config to run the batch in the new location also
Move your batch file somewhere else and make sure you modify your RTS config to run the batch in the new location also
- Posts: 11
- Joined: 24 Jul 2021
Or shoud I just delet the filecopy
- Posts: 3599
- Joined: 11 Jun 2019
You need to keep the batch file. All RTS does is run the command after detecting changes. The command itself runs FFS with the batch file you set up.
- Posts: 11
- Joined: 24 Jul 2021
I am a bit confused. After FFS and RTS setup I created with Editor the batchfile and placed it in startup. The copy should online be my backup notice without any Funktion.
- Posts: 11
- Joined: 24 Jul 2021
Is it nessesary to habe the batchfile also in an other place?
- Posts: 11
- Joined: 24 Jul 2021
I am a bit confused. After FFS and RTS setup I created with Editor the batchfile and placed it in startup. The copy should online be my backup notice without any Funktion.
Is it mandatory to have the batchfile also in a otherer place?
Is it mandatory to have the batchfile also in a otherer place?
- Posts: 3599
- Joined: 11 Jun 2019
I can't understand what you said, sorry.
- Create your sync setup in FFS
- Save as batch file "xxxxxx.ffs_batch" in your documents or wherever you want, as long as it's not in startup
- Open RTS and drag that batch file onto the window so it auto-fills all the info.
- Change idle time if needed, save RTS as xxxxxx.ffs_real in your startup folder
- Done
- Create your sync setup in FFS
- Save as batch file "xxxxxx.ffs_batch" in your documents or wherever you want, as long as it's not in startup
- Open RTS and drag that batch file onto the window so it auto-fills all the info.
- Change idle time if needed, save RTS as xxxxxx.ffs_real in your startup folder
- Done
- Posts: 11
- Joined: 24 Jul 2021
Okay, I got it done and it works perfekt.
Sorry for the confusion last nicht.
Sorry for the confusion last nicht.
- Posts: 3599
- Joined: 11 Jun 2019
No problem, I'm here to help! Glad you got it working!